Deleted
Posts: 0
Dec 1, 2024 0:54:05 GMT
|
Post by Deleted on Oct 16, 2021 14:28:05 GMT
I bought Concord and 9th Sentiments stamp sets (a complete block of words that you can cut out individually). I cannot get it to stamp cleanly. What tips do you have for doing that? It keeps having blank and splotchy parts on it.
I am using a Stamp Platform - should I not be? It doesn't seem to be getting even pressure all across the whole surface of the stamp.
|
|
kelly8875
Pearl Clutcher
Posts: 4,442 
Location: Lost in my supplies...
|
Post by kelly8875 on Oct 16, 2021 14:35:19 GMT
What’s the surface under your paper? Using a glass mat works great.
|
|
Deleted
Posts: 0
Dec 1, 2024 0:54:05 GMT
|
Post by Deleted on Oct 16, 2021 14:38:33 GMT
What’s the surface under your paper? Using a glass mat works great. My table has a glass top - but the Stamp platform is plastic with foam on the bottom. |
|
kelly8875
Pearl Clutcher
Posts: 4,442
Location: Lost in my supplies...
|
Post by kelly8875 on Oct 16, 2021 14:58:09 GMT
The foam on the bottom of the platform might be enough to be throwing it all off. Do you have an acrylic block you can put the stamp on and just use that and your glass mat?
|
|
peasquared
Drama Llama
Posts: 5,773
|
Post by peasquared on Oct 16, 2021 15:02:59 GMT
Does your stamp platform have a reversible lid for rubber and clear stamps? Maybe try using the other side, or using it without the foam?
|
|
JustTricia
Pearl Clutcher
Posts: 2,850
Location: Indianapolis
|
Post by JustTricia on Oct 16, 2021 15:11:15 GMT
Background stamps do better when you put paper to stamp rather than stamp to paper. You can still use the stamp positioner but flip it over so the paper is on the bottom and the stamp is on the top.
|
|
Deleted
Posts: 0
Dec 1, 2024 0:54:05 GMT
|
Post by Deleted on Oct 16, 2021 15:54:46 GMT
I'll give those tips a try! It was so disappointing to have it not work - I have plans for that set. LOL
|
|
|
|
Post by hmp on Oct 16, 2021 16:53:17 GMT
I put the stamp face side up on the table, ink the stamp, put the paper gently on top, then use a brayer to transfer the ink. Make sure you roll the brayer carefully to get the edges & corners.
|
|
|
|
Post by infochick on Oct 16, 2021 17:54:16 GMT
Sometimes it helps to “prime” the stamp too. Just to make sure there isn’t any residue from the manufacturing process. I’ve seen two methods…one where you rub an eraser over the stamp before using, and another where you do the first stamp in Versamark. Either way it can help to clean it first too.
Good luck!
|
|
scrapnnana
Drama Llama
Posts: 6,461
|
Post by scrapnnana on Oct 16, 2021 23:13:23 GMT
I put the stamp face side up on the table, ink the stamp, put the paper gently on top, then use a brayer to transfer the ink. Make sure you roll the brayer carefully to get the edges & corners. This is what I do, too, and it works so much better. |
|
|
|
Post by grammadee on Oct 17, 2021 15:53:58 GMT
I put the stamp face side up on the table, ink the stamp, put the paper gently on top, then use a brayer to transfer the ink. Make sure you roll the brayer carefully to get the edges & corners. I am going to try this. I have had trouble with a couple of all over greeting stamps: they left gaps no matter whether I used a stamp positioner or acrylic block, whether on glass mat or CTMH stamping mat on a solid counter. Thinking the paper/cs would mold itself to the large stamp surface to get a better all over image. |
|
|
|
Post by joblackford on Oct 17, 2021 18:57:34 GMT
Yup, I’ve switched to laying the stamp on its back and putting the paper down on top. I usually place a sheet of copy paper over the top and gently rub over the whole surface with the palm of my hand, or you can use a printmaking baren (or the whiteboard eraser/stamp platform pressure tools that everyone is making or buying) or a brayer. Saves a lot of frustration even if you do have to be careful pulling the paper up. Hope you can get it to work. C&9th make some great stamps  |
|
|
|
Post by riversong1963 on Oct 17, 2021 20:54:39 GMT
Stamp (face-up) on the bottom and paper on top, whether you are using a platform or putting the stamp on your table. If you're using a positioner/platform, tape the paper to the lid, and put the stamp on the bottom part of the platform. It should cling to the plate. If you're using a table, keep the fingers of one hand on the paper while you slowly work your way around the stamp with the fingers of your other hand.
|
|
|
|
Post by Eddie-n-Harley on Oct 17, 2021 21:00:35 GMT
When I am having difficulty getting an image to stamp cleanly with my stamp positioner, I find that it usually helps if I stand up when I'm making the impression (i.e., pushing down on the positioner lid). Must be that I have better leverage and more pressure from a standing position, but it usually fixes any uneven stamping issues I have (especially if there's one spot I just can't get no matter how many times I RE-stamp.)
|
|
Deleted
Posts: 0
Dec 1, 2024 0:54:05 GMT
|
Post by Deleted on Oct 18, 2021 10:40:04 GMT
|
|
pamelakay
Full Member
Posts: 102
Oct 14, 2021 22:33:22 GMT
|
Post by pamelakay on Oct 19, 2021 23:23:02 GMT
Oh I like this, thank you for sharing it! |
|
Deleted
Posts: 0
Dec 1, 2024 0:54:05 GMT
|
Post by Deleted on Oct 20, 2021 10:38:41 GMT
Oh I like this, thank you for sharing it! You are welcome! |
|
|
|
Post by mrsp on Oct 21, 2021 0:59:24 GMT
Sometimes when using a large clear background stamp, if there are small “bubbles” in the way the stamp is adhered to the platform, it won’t give a clear impression. Just a suggestion.
|
|
|
|
Post by julieinsweden on Oct 22, 2021 5:07:28 GMT
When using my stamp positioner on my glass mat on my wobbly table, I can not get a good image even on small stamps. I have to put the positioner on the floor to make sure it has enough support to not bend.
|
|
|
|
Post by dewryce on Oct 22, 2021 17:55:00 GMT
I always start adding paper shims underneath my paper.
|
|
